Escola Superior de Tecnologia e Gestão
Permanent URI for this community
Browse
Browsing Escola Superior de Tecnologia e Gestão by Sustainable Development Goals (SDG) "03:Saúde de Qualidade"
Now showing 1 - 10 of 232
Results Per Page
Sort Options
- A 1.2V 900nW conductance converterPublication . Miranda, Nuno; Morais, RaulThis article describes a new electrical conductance converter method suitable for very low power applications, where energy constraints prevails over speed and measurement accuracy. Method idea gather voltage time integration and shopper stabilization techniques to process noisy low amplitude signals and to overcome severe limitations of weak inversion channel CMOS circuitry. Main features and tradeoffs are exploited. A 1.2V ASIC implementation on standard 0.35μm CMOS schematics is also presented. Post-layout simulations shows a total power consumption lower than 900nW including current source excitation inherent to the conductance measurement. Such low power consumption allows the measurement of several physical parameters on self-powered wireless networks.
- 3D Indoor Radio Coverage for 5G Planning: a Framework of Combining BIM with Ray-tracingPublication . Louro, João; Fernandes, Telmo Rui; Rodrigues, Hugo; Caldeirinha, Rafael F. S.This paper presents a framework to predict indoor radio wave coverage in buildings. Such method includes the capability to import BIM (Building Information Modelling) files that contain structured physical geometry and dimension data, including the material types that are of uttermost importance in evaluating their dielectric properties. Appropriated extraction of physical and dielectric attributes of the building elements was used as input to a 3D radio wave propagation ray-tracing developed in MatLab that allows the prediction of the received radio signal level at any location within the computational volume. Results are presented for line-of-sight contributions and first and second order reflections. Despite the generic nature of the proposed framework, prediction results are presented at 3.6 GHz, envisaging emerging 5G indoor radio coverage.
- 3D Photo-Fabrication for Tissue Engineering and Drug DeliveryPublication . Brás Pereira, Rúben Filipe; Bartolo, PauloThe most promising strategies in tissue engineering involve the integration of a triad of biomaterials, living cells, and biologically active molecules to engineer synthetic environments that closely mimic the healing milieu present in human tissues, and that stimulate tissue repair and regeneration. To be clinically effective, these environments must replicate, as closely as possible, the main characteristics of the native extracellular matrix (ECM) on a cellular and subcellular scale. Photo-fabrication techniques have already been used to generate 3D environments with precise architectures and heterogeneous composition, through a multi-layer procedure involving the selective photocrosslinking reaction of a light-sensitive prepolymer. Cells and therapeutic molecules can be included in the initial hydrogel precursor solution, and processed into 3D constructs. Recently, photo-fabrication has also been explored to dynamically modulate hydrogel features in real time, providing enhanced control of cell fate and delivery of bioactive compounds. This paper focuses on the use of 3D photo-fabrication techniques to produce advanced constructs for tissue regeneration and drug delivery applications. State-of-the-art photo-fabrication techniques are described, with emphasis on the operating principles and biofabrication strategies to create spatially controlled patterns of cells and bioactive factors. Considering its fast processing, spatiotemporal control, high resolution, and accuracy, photo-fabrication is assuming a critical role in the design of sophisticated 3D constructs. This technology is capable of providing appropriate environments for tissue regeneration, and regulating the spatiotemporal delivery of therapeutics.
- 3D printing of new biobased unsaturated polyesters by microstereo-thermal-lithographyPublication . Gonçalves, Filipa A. M. M.; Costa, Cátia S. M. F.; Fabela, Inês G. P.; Farinha, Dina; Faneca, Henrique; Simões, Pedro N.; Serra, Arménio C.; Bártolo, Paulo J.; Coelho, Jorge F. J.New micro three-dimensional (3D) scaffolds using biobased unsaturated polyesters (UPs) were prepared by microstereo-thermal-lithography (μSTLG). This advanced processing technique offers indubitable advantages over traditional printing methods. The accuracy and roughness of the 3D structures were evaluated by scanning electron microscopy and infinite focus microscopy, revealing a suitable roughness for cell attachment. UPs were synthesized by bulk polycondensation between biobased aliphatic diacids (succinic, adipic and sebacic acid) and two different glycols (propylene glycol and diethylene glycol) using fumaric acid as the source of double bonds. The chemical structures of the new oligomers were confirmed by proton nuclear magnetic resonance spectra, attenuated total reflectance Fourier transform infrared spectroscopy and matrix assisted laser desorption/ionization-time of flight mass spectrometry. The thermal and mechanical properties of the UPs were evaluated to determine the influence of the diacid/glycol ratio and the type of diacid in the polyester's properties. In addition an extensive thermal characterization of the polyesters is reported. The data presented in this work opens the possibility for the use of biobased polyesters in additive manufacturing technologies as a route to prepare biodegradable tailor made scaffolds that have potential applications in a tissue engineering area.
- 3D shape prior active contours for an automatic segmentation of a patient specific femur from a CT scanPublication . Almeida, D.; Folgado, J.; Fernandes, P.R.; Ruben, RuiThe following paper describes a novel approach to a medical image segmentation problem. The fully automated computational procedure receives as input images from CT scan exams of the human femur and returns a three dimensional representation of the bone. This patient specific iterative approach is based in 3D active contours without edges, implemented over a level set framework, on which the evolution of the contour depends on local image parameters which can easily be defined by the user but also on a priori information about the volume to segment. This joint approach will lead to an optimal solution convergence of the iterative method. The resulting point cloud can be an excellent starting point for a Finite Element mesh generation and analysis or the basis for a stereolitography for example.
- 3D-printed multisampling holder for microcomputed tomography applied to life and materials science researchPublication . Vasconcelos, Isabel; Franco, Margarida; Pereira, Mário; Duarte, Isabel; Ginjeira, António; Alves, NunoThe aim of this work was to design, fabricate, test and validate a 3D-printed multisampling holder for multi-analysis by microcomputed tomography. Different raw materials were scanned by microcomputed tomography. The raw material chosen was used to fabricate the holder by 3D printing. To validate the multisampling holder, five teeth were filled with a high density-material and scanned in two ways: a single and a multisampling scan mode. For each tooth, the root canal filling volume, porosity volume, closed pore volume, and open pore volume were calculated and compared when the same tooth was scanned in the two sampling scan mode. ABSplus P430™ allowed a high transmission value (84.3 %), and then it was the polymeric material selected to fabricate the holder. In a single sampling scan mode, the scan duration for scanning five teeth was 87.42 min, contrasting with 21.51 min for a multisampling scan mode, which scanned five teeth at the same time. The scan duration time and the cost using a multisampling holder represented a reduction of 75 % and the data volume generated represented a reduction of 60 %. Comparing the two scan modes, the results also showed that the difference of root canal filling volume, porosity volume, closed pore volume, and open pore volume was not statistically significant (p > .05). The multisampling holder was validated to do multi-analysis by microcomputed tomography without significant loss of quantitative accuracy data, allowing a reduction in scan duration time, imaging cost, and data storage.
- 4D Light Field Disparity Map estimation using Krawtchouk PolynomialsPublication . Lourenco, Rui; Rivero-Castillo, Daniel; Thomaz, Lucas A.; Assuncao, Pedro A. A.; Tavora, Luis M. N.; Faria, Sergio M. M. deThis work presents an improved method to estimate disparity maps obtained from light field cameras using a novel edge detection algorithm based on Krawtchouk polynomials. The proposed method takes advantage of these polynomials to determine gradient information and find the edges based on automatically estimated weak and strong thresholds. The calculated edges in the gray scale epipolar plane image representation of a light field are then used to improve the accuracy of object boundaries in the the disparity map. The proposed method achieves better results when compared to other edge detection algorithms, both in terms of objective and subjective quality, specifically by reducing the mean squared error and the artifacts in the object boundaries. Furthermore, on average, the proposed method outperforms the state-of-the-art depth estimation algorithms, in terms of the objective quality of the final disparity map, namely for the commonly used HCI dataset.
- Ad-hoc changes in IoT-aware business processesPublication . Domingos, Dulce; Martins, Francisco; Martinho, Ricardo; Silva, MárioThe Internet of Things makes it possible to adapt the behaviour of business processes in response to real-time context updates. In addition, physical items can run and validate parts of the business processes and optimise their execution, while reducing message transmissions. State-of-the-art event-driven, service-oriented architecture approaches contribute to enabling inter-organisational collaboration and interoperability of heterogeneous hardware, but their applicability is limited to preplanned, well-structured processes. We take a step forward by supporting ad-hoc changes within business processes, considering changes in the state of the Things; likewise, whenever needed, the software controlling the behaviour of sensors may be dynamically reconfigured as a result of changes in the functional specifications of business processes.
- Adaptive coding tree for complexity control of high efficiency video encodersPublication . Correa, G.; Assunção, P.; Silva Cruz, L. A. da; Agostini, L.The emerging HEVC standard introduces several techniques which increase compression efficiency in comparison to its predecessors. However, such advances are accompanied by increases in computational complexity, limiting the encoder use in computational or power-constrained devices. This paper proposes a novel complexity control method for the future HEVC encoders based on a dynamic adjustment of the newly proposed coding tree structures. The relationship between coding tree depths and the encoding complexity is explored to selectively constrain encoding possibilities in order to not exceed a predefined complexity target. Experimental results show that the encoder computational complexity can be downscaled to 60% with a bit rate increase under 3.5% and a PSNR decrease under 0.1 dB.
- Additive manufactured porous biomaterials targeting orthopedic implants: A suitable combination of mechanical, physical and topological propertiesPublication . Bartolomeu, F.; Dourado, N.; Pereira, F.; Alves, N.; Miranda, G.; Silva, F. S.Orthopedic implants are under incessant advancement to improve their interactions with surrounding bone tissue aiming to ensure successful outcomes for patients. A successful biological interaction between implant and surrounding bone depends on the combination of mechanical, physical and topological properties. Hence, Ti6Al4V cellular structures appear as very promising solutions towards the improvement of conventional orthopedic implants. This work addresses a set of fundamental tools that allow improving the design of Ti6Al4V cellular structures produced by Selective Laser Melting (SLM). Three-point bending tests were carried out to estimate the elastic modulus of the produced structures. Morphological analysis allowed to evaluate the dimensional differences that were noticed between the model CAD and the SLM structures. Finite element models (adjusted CAD) were constructed with the experimentally obtained dimensions to replicate the mechanical response of the SLM structures. Linear correlations were systematically found for the dimensions of the SLM structures as a function of the designed model CAD dimensions. This has also been observed for the measured porosities as a function of the designed CAD models. This data can be used in further FE analyses as design guidelines to help engineers fabricating near-net-shape SLM Ti6Al4V cellular structures. Besides, polished and sandblasted surface treatments performed on the Ti6Al4V cellular structures allowed to obtain suitable properties regarding roughness and wettability when compared to as-produced surfaces. The capillarity tests showed that all the analyzed Ti6Al4V structures are able to transport fluid along its structure. The cell viability tests demonstrate Ti6Al4V cellular structures SLM produced did not release toxic substances to the medium, indicating that these structures can assure a suitable environment for cells to proliferate and attach. This study proposes a design methodology for Ti6Al4V cellular structures, that owe suitable mechanical properties but also provide a proper combination of porosity, roughness, wettability, capillarity and cell viability, all of them relevant for orthopedic applications. A Ti6Al4V cellular structured hip implant prototype gathering the suitable features addressed in this study was successfully SLM-produced.