Percorrer por autor "Manuel, Neves"
A mostrar 1 - 3 de 3
Resultados por página
Opções de ordenação
- Influence of Tool Geometry and Process Parameters on Torque, Temperature, and Quality of Friction Stir Welds in Dissimilar Al AlloysPublication . Manuel, Neves; Beltrão, Daniel; Galvão, Ivan; Leal, Rui M.; Costa, José D.; Loureiro, AltinoIn the current investigation, the influence of the tool geometry, the position of the materials in the joint, the welding speed on the temperature and torque developed, and on the quality of the welds in dissimilar and tri-dissimilar T joints were analysed. The aluminium alloys used were AA2017-T4, AA6082-T6, and AA5083-H111 and the friction stir welds were performed with identical shoulder tools, but with either a pin with simple geometry or a pin with progressive geometry. Progressive pin tools proved to be a viable alternative in the production of dissimilar and tri-dissimilar welds, as they provide a larger tool/material friction area and a larger volume of dragged material, which promotes an increase in the heat generated and a good mixing of the materials in the stir zone, although they require a higher torque. Placing a stronger material on the advancing side also results in a higher temperature in the stir zone but requires higher torque too. The combination of these factors showed that tools with a progressive pin provide sound dissimilar and tri-dissimilar welds, unlike single-pin tools. The increase in the welding speed causes the formation of defects in the stir zone, even in tri-dissimilar welds carried out with a tool with a progressive pin, which impairs the fatigue strength of the welds.
- INFLUÊNCIA DA GEOMETRIA DA FERRAMENTA E DAS PROPRIEDADES DE LIGAS DE ALUMÍNIO NA QUALIDADE DAS SOLDADURAS POR FRICTION STIR WELDINGPublication . Manuel, Neves; Beltrão, Daniel; Leal, Rui; Galvão, Ivan; Domingos, José; Loureiro, AltinoO estabelecimento de juntas T entre ligas de alumínio de séries diferentes tem grande importância no caso de estruturas com elevada rigidez, mas com peso reduzido. O processo de soldadura Friction Stir Welding (FSW) apresenta elevado potencial para esta tarefa. O objetivo deste trabalho é investigar a influência da geometria da ferramenta, das propriedades dos materiais e de parâmetros do processo na qualidade de soldaduras FSW dissimilares. A qualidade das soldaduras foi investigada com base na análise da evolução da força axial, binário e ciclo térmico gerado durante a soldadura, bem como na resistência mecânica e sanidade das mesmas. A utilização de ferramentas com pino progressivo, independentemente da posição relativa dos materiais base (placa ou reforço), requer maior força axial da ferramenta, maior rácio velocidade de rotação sobre velocidade de avanço da mesma e maior binário, mas proporciona soldaduras sem defeitos, ao contrário das ferramentas de pino simples.
- Nugget Formation and Mechanical Behaviour of Friction Stir Welds of Three Dissimilar Aluminum AlloysPublication . Manuel, Neves; Galvão, Ivan; Leal, Rui M.; Costa, José D.; Loureiro, AltinoThe aim of this research was to investigate the influence of the properties of the base materials and welding speed on the morphology and mechanical behavior of the friction stir welds of three dissimilar aluminum alloys in a T-joint configuration. The base materials were the AA2017-T4, AA5083-H111, and AA6082-T6 alloys in 3 mm-thick sheets. The AA6082-T6 alloy was the stringer, and the other alloys were located either on the advancing or retreating sides of the skin. All the T-joint welds were produced with a constant tool rotation speed but with different welding speeds. The microstructures of the welds were analyzed using optical microscopy, scanning electron microscopy with energy dispersive spectroscopy, and the electron backscatter diffraction technique. The mechanical properties were assessed according to micro-hardness, tensile, and fatigue testing. Good quality welds of the three dissimilar aluminum alloys could be achieved with friction stir welding, but a high ratio between the tool's rotational and traverse speeds was required. The welding speed influenced the weld morphology and fatigue strength. The positioning of the skin materials influenced the nugget morphology and the mechanical behavior of the joints. The joints in which the AA2017 alloy was positioned on the advancing side presented the best tensile properties and fatigue strength.