Smart design of Titanium/NiTi cellular structured implants by Multi-Material-Selective-Laser-Melting

Funder

Organizational Unit

Publications

Multi-material Ti6Al4V & PEEK cellular structures produced by Selective Laser Melting and Hot Pressing: A tribocorrosion study targeting orthopedic applications

Publication . Bartolomeu, F.; Buciumeanu, M.; Costa, M.M.; Alves, N.; Gasik, M.; Silva, F.S.; Miranda, G.

Ti6Al4V-alloy is commonly used in dental and orthopedic applications where tribochemical reactions occur at material/bone interface. These reactions are one of the main concerns regarding Ti6Al4V implants due to the generation of wear particles, linked to the release of metallic ions in toxic concentration which occurs when TiO2 passive film is destroyed by means of wear and corrosion simultaneously. In the present study, a multi-material Ti6Al4V-PEEK cellular structure is proposed. Selective Laser Melting technique was used to produce Ti6Al4V dense and cellular structured specimens, whilst Hot-Pressing technique was employed to obtain multi-material Ti6Al4V-PEEK structures. This study investigates the tribocorrosion behavior of these materials under reciprocating sliding, comparing them with commercial forged Ti6Al4V. Open-circuit-potential was measured before, during and after sliding while dynamic coefficient of friction was assessed during sliding. The results showed an improved wear resistance and a lower tendency to corrosion for the multi-material Ti6Al4V-PEEK specimens when compared to dense and cellular structures mono-material specimens. This multi-material solution gathering Ti6Al4V and PEEK, besides being able to withstand the loads occurring after implantation on dental and orthopedic applications, is a promising alternative to fully dense metals once it enhances the tribocorrosion performance.

2019Journal article

Open access

Development of β-TCP-Ti6Al4V structures: Driving cellular response by modulating physical and chemical properties

Publication . Costa, M.M.; Lima, R.; Melo-Fonseca, F.; Bartolomeu, F.; Alves, N.; Miranda, A.; Gasik, M.; Silva, F.S.; Silva, N.A.; Miranda, G.

Load-bearing implants success is strongly dependent on several physical and chemical properties that are known to drive cellular response. In this work, multi-material β-TCP-Ti6Al4V cellular structures were designed to combine Ti6Al4V mechanical properties and β-Tricalcium Phosphate bioactivity, in order to promote bone ingrowth as the bioactive material is being absorbed and replaced by newly formed bone. In this sense, the produced structures were characterized regarding roughness, wettability, β-TCP quantity and quality inside the structures after fabrication and the pH measured during cell culture (as consequence of β-TCP dissolution) and those aspects were correlated with cellular viability, distribution, morphology and proliferation. These structures displayed a hydrophilic behavior and results showed that the addition of β-TCP to these cellular structures led to an alkalization of the medium, aspect that significantly influences the cellular response. Higher impregnation ratios were found more adequate for lowering the media pH and toxicity, and thus enhance cell adhesion and proliferation.

2019Journal article

Open access

Corrosion behaviour of PEEK or β-TCP-impregnated Ti6Al4V SLM structures targeting biomedical applications

Publication . Costa, M.M.; Dantas, T.A.; Bartolomeu, F.; Alves, N.; Silva, F.S.; Miranda, G.; Toptan, F.

Ti6Al4V cellular structures were produced by selective laser melting (SLM) and then filled either with beta-tricalcium phosphate (β-TCP) or PEEK (poly-ether-ether-ketone) through powder metallurgy techniques, to improve osteoconductivity and wear resistance. The corrosion behavior of these structures was explored considering its importance for the long-term performance of implants. Results revealed that the incorporation of open cellular pores induced higher electrochemical kinetics when being compared with dense structures. The impregnation of β-TCP and PEEK led to the creation of voids or gaps between the metallic matrix and the impregnated material which also influenced the corrosion behavior of the cellular structures.

2019-12Journal article

Open access

Tribological behavior of bioactive multi-material structures targeting orthopedic applications

Publication . Costa, M.M.; Bartolomeu, F.; Alves, N.; Silva, F.S.; Miranda, G.

The following study proposes a multi-material solution in which Ti6Al4V cellular structures produced by Selective Laser Melting are impregnated with bioactive materials (hydroxyapatite or β-tricalcium phosphate) using press and sintering technique. To assess the tribological response of these structures, an alumina plate was used as a counterpart in a flat-on-flat reciprocating sliding test. Ti6Al4V cellular structures impregnated with bioactive materials displayed the highest wear resistance when compared with the unreinforced structures. Among the bioactive structures, Ti6Al4V cellular structures impregnated with βTCP were the ones with higher wear resistance, having the lowest weight loss. Hence, these structures are promising multifunctional solutions for load-bearing applications by gathering suitable mechanical properties (strength and stiffness); bioactive properties and in addition an improved wear performance.

2019Journal article

Open access

Implant surface design for improved implant stability: A study on Ti6Al4V dense and cellular structures produced by Selective Laser Melting

Publication . Bartolomeu, F.; Costa, M.M.; Gomes, J.R.; Alves, N.; Silva, F.S.; Miranda, G.

Focusing on implant surface design, aiming to improve implant primary stability, SLM technology was explored to produce dense and cellular structured Ti6Al4V specimens. The SLM specimens and also a commercial casted/forged Ti6Al4V group, were sandblasted and acid-etched to obtain a moderate surface roughness topography, typically used in implant manufacturing. Ti6Al4V-bone interaction and tribological performance were assessed by performing sliding tests aiming to replicate in some extension the insertion of a hip implant. The results shown a 24 and 32% higher kinetic friction coefficient values when comparing the cellular structures with the conventional casted/forged Ti6Al4V. These friction results together with a high amount of adhered bone are promising evidences of a higher efficiency of Ti6Al4V cellular structures for enhancing implant stability.

2019Journal article

Restricted access